Refine
Year
- 2017 (1058) (remove)
Publication Type
- Article (312)
- Lecture (227)
- Part of a Book (171)
- Bachelor Thesis (138)
- Master's Thesis (81)
- Book (54)
- Conference Proceeding (54)
- Contribution to a Periodical (7)
- Participation in a Norm (DIN, RFC etc.) (7)
- Report (5)
Language
- German (702)
- English (297)
- Multiple languages (59)
Has Fulltext
- no (1058) (remove)
Keywords
- Umnutzung (19)
- Münster (16)
- Wohnraum (16)
- Neubau (12)
- Migration (10)
- Nachhaltigkeit (10)
- Städtebau (10)
- Raum (8)
- Sanierung (8)
- Flüchtlinge (7)
Faculty
- Sozialwesen (SW) (209)
- Architektur (MSA) (151)
- Gesundheit (MDH) (116)
- Wirtschaft (MSB) (85)
- Energie · Gebäude · Umwelt (EGU) (80)
- Chemieingenieurwesen (CIW) (79)
- Studiengang Soziale Arbeit (70)
- Physikingenieurwesen (PHY) (62)
- Oecotrophologie · Facility Management (OEF) (54)
- IBL (51)
- Bauingenieurwesen (BAU) (50)
- Elektrotechnik und Informatik (ETI) (33)
- Wandelwerk. Zentrum für Qualitätsentwicklung (25)
- Maschinenbau (MB) (24)
- Design (MSD) (22)
- iSuN Institut für Nachhaltige Ernährung (13)
- ITB (12)
- keine Zuordnung (9)
- Center for Real Estate & Organization Dynamics (8)
- Kompetenzzentrum Humanitäre Hilfe (1)
- Oecotrophologie · Facility Management (1)
From transformative Leadership to transformative Learning. New Approaches in Leadership Development
(2017)
Sediment transport in high-speed flows over a fixed bed. 2: Particle impacts and abrasion prediction
(2017)
Single bed load particle impacts were experimentally investigated in supercritical open channel flow over a fixed planar bed of low relative roughness height simulating high-gradient non-alluvial mountain streams as well as hydraulic structures. Particle impact characteristics (impact velocity, impact angle, Stokes number, restitution and dynamic friction coefficients) were determined for a wide range of hydraulic parameters and particle properties. Particle impact velocity scaled with the particle velocity, and the vertical particle impact velocity increased with excess transport stage. Particle impact and rebound angles were low and decreased with transport stage. Analysis of the particle impacts with the bed revealed almost no viscous damping effects with high normal restitution coefficients exceeding unity. The normal and resultant Stokes numbers were high and above critical thresholds for viscous damping. These results are attributed to the coherent turbulent structures near the wall region, i.e. bursting motion with ejection and sweep events responsible for turbulence generation and particle transport. The tangential restitution coefficients were slightly below unity and the dynamic friction coefficients were lower than for alluvial bed data, revealing that only a small amount of horizontal energy was transferred to the bed. The abrasion prediction model formed by Sklar and Dietrich in 2004 was revised based on the new equations on vertical impact velocity and hop length covering various bed configurations. The abrasion coefficient kv was found to be vary around kv ~ 105 for hard materials (tensile strength ft > 1 MPa), one order of magnitude lower than the value assumed so far for Sklar and Dietrich's model.
Particle dynamics are investigated experimentally in supercritical high-speed open channel flow over a fixed planar bed of low relative roughness height simulating flows in high-gradient non-alluvial mountain streams and hydraulic structures. Non-dimensional equations were developed for transport mode, particle velocity, hop length and hop height accounting for a wide range of literature data encompassing sub- and supercritical flow conditions as well as planar and alluvial bed configurations. Particles were dominantly transported in saltation and particle trajectories on planar beds were rather flat and long compared with alluvial bed data due to (1) increased lift forces by spinning motion, (2) strongly downward directed secondary currents, and (3) a planar flume bed where variation in particle reflection and damping effects were minor. The analysis of particle saltation trajectories revealed that the rising and falling limbs were almost symmetrical contradicting alluvial bed data. Furthermore, no or negligible effect of particle size and shape on particle dynamics were found. Implications of experimental findings for mechanistic saltation-abrasion models are briefly discussed.
Four dams in Japan and Switzerland with Sediment Bypass Tunnels (SBT) as a measure against reservoir sedimentation were monitored to analyse the effects of sediment supply on the downstream environment based on up- to downstream differences in geomorphological and biological characteristics. SBT operation times ranged from 93 years at Pfaffensprung and 17 at Asahi to only three years at Solis and no operation at Koshibu. Sediment grain size distribution was monitored, and microhabitats and invertebrates were analysed in terms of richness and composition. Results showed that grain sizes were coarser down- than upstream at dams with newly established SBTs, while they were similar or finer for dams with long SBT operation. Analysis of biotic data revealed that microhabitat and invertebrate richness was low directly below the dam but increased further downstream the longer the SBT operation. Sedentary species dominated at locations where bed conditions were stable, e.g. directly downstream of the dam at Koshibu. Recovery of downstream environment with increasing SBT operation time was disclosed by the Bray–Curtis similarity index, which evaluated an overlap between up- and downstream reaches for both microhabitat composition and invertebrate communities. With increasing operation time, both indices increased, revealing the positive effects of long-term SBT operation.
The thermal conditions like the temperature distribution and the heat fluxes during metal cutting have a major influence on the machinability, the tool lifetime, the metallurgical structure and thus the functionality of the work piece. This in particular applies for manufacturing processes like milling, drilling and turning for high-value turbomachinery components like impellers, combustion engines and compressors of the aerospace and automotive industry as well as energy generation, which play a major role in modern societies. However, numerous analytical and experimental efforts have been conducted in order to understand the thermal conditions in metal cutting, yet many questions still prevail. Most models are based on a stationary point of view and do not include time dependent effects like in intensity and distribution varying heat sources, varying engagement conditions and progressive tool wear. In order to cover such transient physics an analytical approach based on Green’s functions for the solution of the partial differential equations of unsteady heat conduction in solids is used to model entire transient temperature fields. The validation of the model is carried out in orthogonal cutting experiments not only punctually but also for entire temperature fields. For these experiments an integrated measurement of prevailing cutting force and temperature fields in the tool and the chip by means of high-speed thermography were applied. The thermal images were analyzed with regard to thermodynamic energy balancing in order to derive the heat partition between tool, chips and workpiece. The thus calculated heat flow into the tool was subsequently used in order to analytically model the transient volumetric temperature fields in the tool. The described methodology enables the modeling of the transient thermal state in the cutting zone and particular in the tool, which is directly linked to phenomena like tool wear and workpiece surface modifications.