Refine
Publication Type
- Conference Proceeding (10)
- Article (6)
Due to high bedload sediment transport, many sediment bypass tunnels (SBT) are prone to severe invert abrasion. However, there is little information about the flow characteristics in SBTs after invert abrasion initiated and progresses with time. In the present study, laboratory flume experiments were performed to investigate how the hydraulic conditions change after abrasion patterns developed on the invert. A typical invert abrasion pattern was produced using 3D-printing technique and implemented in the laboratory flume. Flow depths were measured to compare the initial with the abraded state.
Furthermore, turbulence measurements using 2D-laser Doppler anemometry technique were performed to obtain the mean and turbulence flow characteristics. This paper describes results of these measurements focusing on the streamwise and vertical flow velocities, turbulence intensities and Reynolds shear stress.
Positive effects of reservoir sedimentation management on reservoir life: Examples from Japan
(2016)
The effectiveness of different strategies against reservoir sedimentation is demonstrated herein using data sets of Asahi, Nunobiki and Dashidaira reservoirs in Japan. The applied strategies encompass
sediment routing with a bypass tunnel, drawdown flushing during floods and sabo dam construction in the catchment. It is shown that bypassing and flushing are very efficient strategies enlarging reservoir life by 3 to 21 times up to many hundreds of years. Furthermore, it is revealed that also efforts in the catchment, e.g. sabo dam construction, is effective enlarging reservoir life by 2.4 times.
Sediment transport in high-speed flows over a fixed bed. 2: Particle impacts and abrasion prediction
(2017)
Single bed load particle impacts were experimentally investigated in supercritical open channel flow over a fixed planar bed of low relative roughness height simulating high-gradient non-alluvial mountain streams as well as hydraulic structures. Particle impact characteristics (impact velocity, impact angle, Stokes number, restitution and dynamic friction coefficients) were determined for a wide range of hydraulic parameters and particle properties. Particle impact velocity scaled with the particle velocity, and the vertical particle impact velocity increased with excess transport stage. Particle impact and rebound angles were low and decreased with transport stage. Analysis of the particle impacts with the bed revealed almost no viscous damping effects with high normal restitution coefficients exceeding unity. The normal and resultant Stokes numbers were high and above critical thresholds for viscous damping. These results are attributed to the coherent turbulent structures near the wall region, i.e. bursting motion with ejection and sweep events responsible for turbulence generation and particle transport. The tangential restitution coefficients were slightly below unity and the dynamic friction coefficients were lower than for alluvial bed data, revealing that only a small amount of horizontal energy was transferred to the bed. The abrasion prediction model formed by Sklar and Dietrich in 2004 was revised based on the new equations on vertical impact velocity and hop length covering various bed configurations. The abrasion coefficient kv was found to be vary around kv ~ 105 for hard materials (tensile strength ft > 1 MPa), one order of magnitude lower than the value assumed so far for Sklar and Dietrich's model.
To achieve the sustainable use of dams, the development of methods for sediment management in reservoirs is required. One such method includes the use of Sediment Bypass Tunnels (SBTs) to divert sediment around a dam, thereby preventing sedimentation in the reservoir. However, SBTs are prone to severe invert abrasion caused by the high sediment flux. Therefore, it is necessary to establish a measurement system of the sediment transport rate in these tunnels. One system to measure sediment transport in rivers is the Swiss plate geophone, which can register plate vibrations caused by particle impact. In Japan, the Japanese pipe microphone is used, and sediment transport is measured based on the sound emitted by the particle impact. In this study an attempt was made to optimize the advantages of both systems by fixing a microphone and an acceleration sensor to a steel plate. The results of calibration experiments with this new system are presented and compared with the existing methods. It was found that the acceleration sensor can detect sediment particles larger than 2 mm in diameter. Moreover, a new parameter, referred to as the detection rate, was introduced to describe the correlation between the actual amount of sediment and the registered output. Finally, two parameters - the saturation rate and hit rate - are introduced and exhibit strong correlation with the detection rate.
Four dams in Japan and Switzerland with Sediment Bypass Tunnels (SBT) as a measure against reservoir sedimentation were monitored to analyse the effects of sediment supply on the downstream environment based on up- to downstream differences in geomorphological and biological characteristics. SBT operation times ranged from 93 years at Pfaffensprung and 17 at Asahi to only three years at Solis and no operation at Koshibu. Sediment grain size distribution was monitored, and microhabitats and invertebrates were analysed in terms of richness and composition. Results showed that grain sizes were coarser down- than upstream at dams with newly established SBTs, while they were similar or finer for dams with long SBT operation. Analysis of biotic data revealed that microhabitat and invertebrate richness was low directly below the dam but increased further downstream the longer the SBT operation. Sedentary species dominated at locations where bed conditions were stable, e.g. directly downstream of the dam at Koshibu. Recovery of downstream environment with increasing SBT operation time was disclosed by the Bray–Curtis similarity index, which evaluated an overlap between up- and downstream reaches for both microhabitat composition and invertebrate communities. With increasing operation time, both indices increased, revealing the positive effects of long-term SBT operation.
Particle dynamics are investigated experimentally in supercritical high-speed open channel flow over a fixed planar bed of low relative roughness height simulating flows in high-gradient non-alluvial mountain streams and hydraulic structures. Non-dimensional equations were developed for transport mode, particle velocity, hop length and hop height accounting for a wide range of literature data encompassing sub- and supercritical flow conditions as well as planar and alluvial bed configurations. Particles were dominantly transported in saltation and particle trajectories on planar beds were rather flat and long compared with alluvial bed data due to (1) increased lift forces by spinning motion, (2) strongly downward directed secondary currents, and (3) a planar flume bed where variation in particle reflection and damping effects were minor. The analysis of particle saltation trajectories revealed that the rising and falling limbs were almost symmetrical contradicting alluvial bed data. Furthermore, no or negligible effect of particle size and shape on particle dynamics were found. Implications of experimental findings for mechanistic saltation-abrasion models are briefly discussed.
Abrasion in a concrete-lined sediment bypass tunnel is estimated using a Japanese state-of-the-art prediction model and validated by measured invert abrasion data at Asahi Reservoir, Japan. The model is described in detail, certain shortcomings are disclosed, and a revised version is proposed. The model consists of a kinetic energy term accounting for the impact by saltating particles, and a friction work term accounting for the grinding stress. It is found that the latter term yields concrete abrasion values being consistently a multiple compared to its kinetic term contradicting other research. Based on that, and a possible particle impact angle inconsistency, it is proposed to omit the friction work term. It is shown that the calculated abrasion is overestimated by 138% on average compared with that measured, if both terms are accounted for. However, promising results are obtained with only 30% overestimation by neglecting the friction work term.
Sediment, which deposits and damages the function of reservoirs, is an essential element of aquatic habitats in downstream ecosystems. We reviewed ecosystem features of degraded channels associated with sediment deficiency below dams and ecosystem responses to changes in sediment conditions after management practices in Japan. Sediment bypass tunnel (SBT) is an effective way to transport sufficient amount of sediment to downstream ecosystems. Based on a concept of suitable mass and size of sediment for ecosystem, some effects and limitations of SBT on downstream ecosystems were discussed.
Sediment bypass tunnels are an effective and sustainable strategy against reservoir sedimentation. Sediments are diverted into the down-stream during floods without deposition in the reservoir, hence mor-phological and ecological variability increases. One major drawback of these tunnels is the severe invert abrasion due to a combination of high flow velocities and bedload sediment transport. The abrasion phenom-ena is briefly described, different abrasion prediction models are pre-sented and their applicability for the estimation of concrete abrasion is discussed.