Energie · Gebäude · Umwelt (EGU)
Refine
Year
- 2022 (24) (remove)
Publication Type
- Article (24) (remove)
Keywords
- Trinkwasserinstallation (3)
- energy system modeling (2)
- urban energy systems (2)
- 10 x DN (1)
- AFS63 (1)
- Abfiltrierbare Stoffe (1)
- Abwasserhebeanlage (1)
- Armaturenanschluss (1)
- Einzelzuleitung PWH (1)
- Filter-Lamella-Separator (1)
Faculty
Flexible biogas production can enable demand-oriented energy supply without the need for expensive gas storage expansions, but poses challenges to the stability of the anaerobic digestion (AD) process. In this work, biogas production of laboratory-scale AD of maize silage and sugar beets was optimized to cover the residual load of an electricity self-sufficient community using a simple process model based on first-order kinetics. Experiments show a good agreement between biogas demand, predicted, and measured biogas production. By optimizing biogas conversion schedules based on the measured gas production, a gas storage capacity of 7-8 h was identified for maximum flexibility, which corresponds to typical gas storage sizes at industrial biogas plants in Germany. Various stability indicators were continuously monitored and proved resilient process conditions. These results demonstrate that demand-oriented biogas production using model predictive control is a promising approach to enable existing biogas plants to provide balancing energy.
The development of compact treatment devices with high removal efficiencies and low space requirements is a key objective of urban stormwater
treatment. Thus, many devices utilize a combination of sedimentation and upward flow filtration in a single system. This study, for the
first time, evaluates the flow field inside a combined filter-lamella separator via computational fluid dynamics. Herein, three objectives
are investigated: (i) the flow field for different structural configurations, (ii) the distribution of particulate matter along the filter bed and
(iii) the dynamic clogging in discrete filter zones, which is addressed by a clogging model derived from literature data. The results indicate
that a direct combination of a filtration stage with a lamella separator promotes a uniform flow distribution. The distribution of particulate
matter along the filter bed varies with configuration and particle size. Clogging, induced by particles in the spectrum ,63 μm, creates
gradients of hydraulic conductivity along the filter bed. After treating about half of Germany’s annual runoff-efficient precipitation at a rainfall
intensity of 5 L/(s·ha), the filtration rates increase in the front of the filter bed by þ10%. Thus, long-term operating behavior is sensitive to
efficient filter utilization in compact treatment devices.
Indicators for the optimization of sustainable urban energy systems based on energy system modeling
(2022)
Background: Urban energy systems are responsible for 75 % of the world's energy consumption and for 70 % of the worldwide greenhouse gas emissions. Energy system models are used to optimize, benchmark and compare such energy systems with the help of energy sustainability indicators. We discuss several indicators for their basic suitability and their response to changing boundary conditions, system structures and reference values. The most suitable parameters are applied to four different supply scenarios of a real-world urban energy system.
Results: There is a number of energy sustainability indicators, but not all of them are suitable for the use in urban energy system optimization models. Shortcomings originate from the omission of upstream energy supply chains (secondary energy efficiency), from limited capabilities to compare small energy systems (energy productivity), from excessive accounting expense (regeneration rate), from unsuitable accounting methods (primary energy efficiency), from a questionable impact of some indicators on the overall system sustainability (self-sufficiency), from the lack of detailed information content (share of renewables), and more. On the other hand, indicators of absolute greenhouse gas emissions, energy costs, and final energy demand are well suitable for the use in optimization models. However, each of these indicators only represents partial aspects of energy sustainability; the use of only one indicator in the optimization process increases the risk that other important aspects will deteriorate significantly, eventually leading to suboptimal or even unrealistic scenarios in practice. Therefore, multi-criteria approaches should be used to enable a more holistic optimization and planning of sustainable urban energy systems.
Conclusion: We recommend multi-criteria optimization approaches using the indicators of absolute greenhouse gas emissions, absolute energy costs, and absolute energy demand. For benchmarking and comparison purposes, specific indicators should be used and therefore related to the final energy demand, respectively the number of inhabitants. Our example scenarios demonstrate modeling strategies to optimize sustainability of urban energy systems.
(1) The use of renewable energy for power and heat supply is one of the strategies to reduce greenhouse gas emissions. As only 14% of German households are supplied with renewable energy, a shift is necessary. This shift should be realized with the lowest possible environmental impact. This paper assesses the environmental impacts of changes in energy generation and distribution, by integrating the life cycle assessment (LCA) method into energy system models (ESM). (2) The integrated LCA is applied to a case study of the German neighborhood of Herne, (i) to optimize the energy supply, considering different technologies, and (ii) to determine the environmental impacts of the base case (status quo), a cost-optimized scenario, and a CO2-optimized scenario. (3) The use of gas boilers in the base case is substituted with CHPs, surface water heat pumps and PV-systems in the CO2-optimized scenario, and five ground-coupled heat pumps and PV-systems for the cost-optimized scenario. This technology shift led to a reduction in greenhouse gas emissions of almost 40% in the cost-optimized, and more than 50% in the CO2-optimized, scenario. However, technology shifts, e.g., due to oversized battery storage, risk higher impacts in other categories, such as terrestrial eco toxicity, by around 22%. Thus, it can be recommended to use smaller battery storage systems. (4) By combining ESM and LCA, additional environmental impacts beyond GHG emissions can be quantified, and therefore trade-offs between environmental impacts can be identified. Furthermore, only applying ESM leads to an underestimation of greenhouse gas emissions of around 10%. However, combining ESM and LCA required significant effort and is not yet possible using an integrated software.
Heating networks are highly relevant for the achievement of climate protection goals of urban energy systems. This is due to their high renewable energy potential combined with high plant efficiency and utilization rates. For the optimal integration and sector coupling of heating networks in holistic urban energy systems, open source energy system modeling tools are highly recommended. In this contribution, two open source approaches (the "Spreadsheet Energy System Model Generator"-integrated DHNx-Python module (DHNx/SESMG) and Thermos) are theoretically compared, and practically applied to a real-world energy system. Deviations within the results can be explained by incorrectly pre-defined parameters within Thermos and cannot be adjusted by the modeler. The simultaneity is underestimated in the case study by Thermos by more than 20%. This results in undersized heating plant capacities and a 50% higher number of buildings connected to the network. However, Thermos offers a higher end-user usability and over 100 times faster solving. DHNx/SESMG, in contrast, offers the possibility to adjust more model parameters individually and consider multiple energy sectors. This enables a holistic modeling of urban energy systems and the model-based optimization of multi-sectoral synergies.
Techno-Economic Assessment of Solid-Liquid Biogas Treatment Plants for the Agro-Industrial Sector
(2022)
In Germany, the current sectoral urban planning often leads to inefficient use of resources, partly because municipalities lack integrated planning instruments and argumentation strength toward politics, investors, or citizens. The paper develops the ResourcePlan as (i) legal and (ii) a planning instrument to support the efficient use of resources in urban neighborhoods. The integrative, multi-methodological approach addresses the use of natural resources in the building and infrastructural sectors of (i) water (storm- and wastewater) management, (ii) construction and maintenance of buildings and infrastructure, (iii) urban energy system planning, and (iv) land-use planning. First, the development as legal instrument is carried out, providing (i) premises for integrating resource protection at all legal levels and (ii) options for implementing the ResourcePlan within German municipal structures. Second, the evaluation framework for resource efficiency of the urban neighborhoods is set up for usage as a planning instrument. The framework provides a two-stage process that runs through the phases of setting up and implementing the ResourcePlan. (Eco)system services are evaluated as well as life cycle assessment and economic aspects. As a legal instrument, the ResourcePlan integrates resource protection into municipal planning and decision-making processes. The multi-methodological evaluation framework helps to assess inter-disciplinary resource efficiency, supports the spatial identification of synergies and conflicting goals, and contributes to transparent, resource-optimized planning decisions.