Auel, Christian
Refine
Publication Type
- Article (13) (remove)
Hydroabrasion tritt im alpinen Raum hauptsächlich bei Wasserbauwerken auf, die durch hohe Fließgeschwindigkeiten und große Sedimentfrachten belastet werden. Dies sind beispielswei-se Wehrschwellen in Flüssen, Wasserfassungen von Wasserkraftwerken und vor allem Sedi-mentumleitstollen. Letztere dienen dazu sedimentreiche Hochwasserspitzen um die Talsperre herum in den Unterlauf des Flusses zu leiten. Sie verhindern so eine fortschreitende Verlan-dung des Stauraums.
Es gibt verschiedene Konzepte, dem Problem der Hydroabrasion entgegen zu wirken. Einer-seits kann der Umleitstollen hydraulisch optimiert werden, um die Einwirkung auf die Sohle zu minimieren. Auf der anderen Seite kann deren Widerstand verbessert werden. An der Ver-suchsanstalt für Wasserbau, Hydrologie und Glaziologie (VAW) der ETH Zürich werden zur Zeit zwei Forschungsarbeiten durchgeführt, die sich jeweils diesen Aspekten widmen. Dieser Beitrag befasst sich mit der hydraulischen Optimierung von Sedimentumleitstollen mit Hilfe von großskaligen Laborversuchen.
In insgesamt drei Versuchsreihen werden die Mittelwert- und Turbulenz-Fließcharakteristik von schießendem Abfluss in einer Versuchsrinne mittels eines Laser-Doppler Anemometrie-Systems (LDA) aufgenommen, die Fortbewegungsart des Sediments mittels eines High-Speed Kamera-Systems analysiert sowie die Abrasion der Stollensohle untersucht. In Abhängigkeit des Sohlgefälles, des Durchflusses, der Größe und Menge der Sedimentfracht erfolgt die Fortbewegung des Sedimentkorns hüpfend, rollend oder gleitend und verursacht unterschied-liche Abrasionserscheinungen in der Stollensohle. Die Ergebnisse der LDA Experimente zei-gen, dass, abhängig vom Verhältnis Gerinnebreite zur Abflusstiefe, Sekundärströmungen auf-treten. Diese Sekundärströmungen beeinflussen im untersuchten Froude-Zahlenbereich 2, 4 und 8 das longitudinale Strömungsprofil sowie die Verteilung der Sohlen- bzw. Reynolds-Schubspannungen und der Turbulenzintensität und somit letztlich die Fortbewegungsart des Sedimentkorns in der Wassersäule.
Mittels der drei Versuchsreihen sollen bestmögliche hydraulische Bedingungen für Sedimen-tumleitstollen gefunden werden, um die Hydroabrasion und somit die Unterhaltskosten signi-fikant zu minimieren.
An experimental investigation of supercritical uniform and gradually varied open channel flows is presented for a wide range of Froude numbers and flume width-to-flow depth aspect ratios. The instantaneous streamwise and vertical flow velocities were measured in a laboratory flume over the entire width using a two dimensional–laser Doppler anemometry (2D-LDA) system to determine turbulence intensities, and bed and Reynolds shear stresses. The mean velocity patterns show undulation across the flume, indicating the presence of counterrotating secondary current cells. These currents redistribute turbulence intensities and bed and Reynolds shear stresses across the flume. For aspect ratios ≤ 4−5, i.e., narrow open channel flow, the velocity-dip phenomenon is identified both in the streamwise velocity and the Reynolds shear stress distributions. For high aspect ratios, i.e., wide open channel flow, the strength of secondary currents diminish toward the flume center, resulting in a 2D flow farther away from the walls and no velocity-dip phenomenon. Froude number effects on the flow characteristics are less pronounced compared to the aspect ratio effects. At high Froude numbers, the results for narrow and wide open channel flows agree well with literature data. The log-law holds in the inner region across the entire flume width for all investigated Froude numbers and aspect ratios. The Reynolds shear stress distribution agrees well with the computed spanwise bed shear stress distribution. At the flume side walls, the bed shear stresses are 20–50 % higher than the mean values. These results are verified with an engineering example in which high sediment transport and corresponding deep abrasion patterns at the side walls were observed.
Four dams in Japan and Switzerland with Sediment Bypass Tunnels (SBT) as a measure against reservoir sedimentation were monitored to analyse the effects of sediment supply on the downstream environment based on up- to downstream differences in geomorphological and biological characteristics. SBT operation times ranged from 93 years at Pfaffensprung and 17 at Asahi to only three years at Solis and no operation at Koshibu. Sediment grain size distribution was monitored, and microhabitats and invertebrates were analysed in terms of richness and composition. Results showed that grain sizes were coarser down- than upstream at dams with newly established SBTs, while they were similar or finer for dams with long SBT operation. Analysis of biotic data revealed that microhabitat and invertebrate richness was low directly below the dam but increased further downstream the longer the SBT operation. Sedentary species dominated at locations where bed conditions were stable, e.g. directly downstream of the dam at Koshibu. Recovery of downstream environment with increasing SBT operation time was disclosed by the Bray–Curtis similarity index, which evaluated an overlap between up- and downstream reaches for both microhabitat composition and invertebrate communities. With increasing operation time, both indices increased, revealing the positive effects of long-term SBT operation.
Sediment transport in high-speed flows over a fixed bed. 2: Particle impacts and abrasion prediction
(2017)
Single bed load particle impacts were experimentally investigated in supercritical open channel flow over a fixed planar bed of low relative roughness height simulating high-gradient non-alluvial mountain streams as well as hydraulic structures. Particle impact characteristics (impact velocity, impact angle, Stokes number, restitution and dynamic friction coefficients) were determined for a wide range of hydraulic parameters and particle properties. Particle impact velocity scaled with the particle velocity, and the vertical particle impact velocity increased with excess transport stage. Particle impact and rebound angles were low and decreased with transport stage. Analysis of the particle impacts with the bed revealed almost no viscous damping effects with high normal restitution coefficients exceeding unity. The normal and resultant Stokes numbers were high and above critical thresholds for viscous damping. These results are attributed to the coherent turbulent structures near the wall region, i.e. bursting motion with ejection and sweep events responsible for turbulence generation and particle transport. The tangential restitution coefficients were slightly below unity and the dynamic friction coefficients were lower than for alluvial bed data, revealing that only a small amount of horizontal energy was transferred to the bed. The abrasion prediction model formed by Sklar and Dietrich in 2004 was revised based on the new equations on vertical impact velocity and hop length covering various bed configurations. The abrasion coefficient kv was found to be vary around kv ~ 105 for hard materials (tensile strength ft > 1 MPa), one order of magnitude lower than the value assumed so far for Sklar and Dietrich's model.
Particle dynamics are investigated experimentally in supercritical high-speed open channel flow over a fixed planar bed of low relative roughness height simulating flows in high-gradient non-alluvial mountain streams and hydraulic structures. Non-dimensional equations were developed for transport mode, particle velocity, hop length and hop height accounting for a wide range of literature data encompassing sub- and supercritical flow conditions as well as planar and alluvial bed configurations. Particles were dominantly transported in saltation and particle trajectories on planar beds were rather flat and long compared with alluvial bed data due to (1) increased lift forces by spinning motion, (2) strongly downward directed secondary currents, and (3) a planar flume bed where variation in particle reflection and damping effects were minor. The analysis of particle saltation trajectories revealed that the rising and falling limbs were almost symmetrical contradicting alluvial bed data. Furthermore, no or negligible effect of particle size and shape on particle dynamics were found. Implications of experimental findings for mechanistic saltation-abrasion models are briefly discussed.