Sediment transport in high-speed flows over a fixed bed. 2: Particle impacts and abrasion prediction
(2017)
Single bed load particle impacts were experimentally investigated in supercritical open channel flow over a fixed planar bed of low relative roughness height simulating high-gradient non-alluvial mountain streams as well as hydraulic structures. Particle impact characteristics (impact velocity, impact angle, Stokes number, restitution and dynamic friction coefficients) were determined for a wide range of hydraulic parameters and particle properties. Particle impact velocity scaled with the particle velocity, and the vertical particle impact velocity increased with excess transport stage. Particle impact and rebound angles were low and decreased with transport stage. Analysis of the particle impacts with the bed revealed almost no viscous damping effects with high normal restitution coefficients exceeding unity. The normal and resultant Stokes numbers were high and above critical thresholds for viscous damping. These results are attributed to the coherent turbulent structures near the wall region, i.e. bursting motion with ejection and sweep events responsible for turbulence generation and particle transport. The tangential restitution coefficients were slightly below unity and the dynamic friction coefficients were lower than for alluvial bed data, revealing that only a small amount of horizontal energy was transferred to the bed. The abrasion prediction model formed by Sklar and Dietrich in 2004 was revised based on the new equations on vertical impact velocity and hop length covering various bed configurations. The abrasion coefficient kv was found to be vary around kv ~ 105 for hard materials (tensile strength ft > 1 MPa), one order of magnitude lower than the value assumed so far for Sklar and Dietrich's model.
Particle dynamics are investigated experimentally in supercritical high-speed open channel flow over a fixed planar bed of low relative roughness height simulating flows in high-gradient non-alluvial mountain streams and hydraulic structures. Non-dimensional equations were developed for transport mode, particle velocity, hop length and hop height accounting for a wide range of literature data encompassing sub- and supercritical flow conditions as well as planar and alluvial bed configurations. Particles were dominantly transported in saltation and particle trajectories on planar beds were rather flat and long compared with alluvial bed data due to (1) increased lift forces by spinning motion, (2) strongly downward directed secondary currents, and (3) a planar flume bed where variation in particle reflection and damping effects were minor. The analysis of particle saltation trajectories revealed that the rising and falling limbs were almost symmetrical contradicting alluvial bed data. Furthermore, no or negligible effect of particle size and shape on particle dynamics were found. Implications of experimental findings for mechanistic saltation-abrasion models are briefly discussed.
An experimental investigation of supercritical uniform and gradually varied open channel flows is presented for a wide range of Froude numbers and flume width-to-flow depth aspect ratios. The instantaneous streamwise and vertical flow velocities were measured in a laboratory flume over the entire width using a two dimensional–laser Doppler anemometry (2D-LDA) system to determine turbulence intensities, and bed and Reynolds shear stresses. The mean velocity patterns show undulation across the flume, indicating the presence of counterrotating secondary current cells. These currents redistribute turbulence intensities and bed and Reynolds shear stresses across the flume. For aspect ratios ≤ 4−5, i.e., narrow open channel flow, the velocity-dip phenomenon is identified both in the streamwise velocity and the Reynolds shear stress distributions. For high aspect ratios, i.e., wide open channel flow, the strength of secondary currents diminish toward the flume center, resulting in a 2D flow farther away from the walls and no velocity-dip phenomenon. Froude number effects on the flow characteristics are less pronounced compared to the aspect ratio effects. At high Froude numbers, the results for narrow and wide open channel flows agree well with literature data. The log-law holds in the inner region across the entire flume width for all investigated Froude numbers and aspect ratios. The Reynolds shear stress distribution agrees well with the computed spanwise bed shear stress distribution. At the flume side walls, the bed shear stresses are 20–50 % higher than the mean values. These results are verified with an engineering example in which high sediment transport and corresponding deep abrasion patterns at the side walls were observed.