Refine
Year
Publication Type
- Conference Proceeding (63) (remove)
Keywords
- Echtzeitanalyse (2)
- Liner (2)
- AFS/AFS63 (1)
- Altrohrschäden (1)
- Altrohrzustand III (1)
- Argos (1)
- Belastungsfahrzeug (1)
- Belastungsversuche (1)
- Bodenspannungen (1)
- Dezentrale Anlagen (1)
Faculty
- Bauingenieurwesen (BAU) (63) (remove)
Wastewater Generation Model to Predict Impacts of Urine Separation on Wastewater Treatment Plants
(2023)
Wastewater treatment plants are under increasing pressure to enhance resource efficiency and reduce emissions into water bodies. Separation of urine within the catchment area may be an alternative to mitigate the need for costly expansions of central wastewater treatment plant. While previous investigations assumed a spatially uniform implementation of urine separation across the catchment area, the present study introduces a modelling framework which allows to determine the influence of targeted urine separation on the operation and emissions of central wastewater treatment plants. The framework includes an adapted stochastic wastewater generation model, the Stormwater Management Model, and Activated Sludge Model No. 3 with Bio-P module (SIMBA#). The entire application is embedded in the R programming language. The model is validated by an extensive sampling and measurement campaign. Preliminary results based on observed and simulated wastewater generation and transport for a catchment area of 436 residents indicate the suitability of the model for wastewater generation and transport modelling, but also show further need for calibration.
Im Zuge des Klimawandels wird der landwirtschaftliche Bewässerungsbedarf auch in Deutschland zukünftig steigen. Die EU-Verordnung 2020/741 stellt Mindestanforderungen an die Wiederverwendung weitergehend aufbereiteten kommunalen Abwassers zur landwirtschaftlichen Bewässerung, um die Nutzung natürlicher Wasserressourcen hierfür zu begrenzen. Die EU-Verordnung wird am 26. Juni 2023 Gültigkeit erlangen und soll in Deutschland in das Wasserhaushaltsgesetz eingebettet und um eine neue Bundesverordnung ergänzt werden. Zentrales Element der Wasserwiederverwendung wird der für jeden Einzelfall zu erstellende Risikomanagementplan sein, der der Minimierung möglicher hiermit verbundener Risiken dient. Als Hilfestellung für die praktische Umsetzung von Wasserwiederverwendung wird die DWA die Merkblattreihe M-1200 veröffentlichen.
Due to high bedload sediment transport, many sediment bypass tunnels (SBT) are prone to severe invert abrasion. However, there is little information about the flow characteristics in SBTs after invert abrasion initiated and progresses with time. In the present study, laboratory flume experiments were performed to investigate how the hydraulic conditions change after abrasion patterns developed on the invert. A typical invert abrasion pattern was produced using 3D-printing technique and implemented in the laboratory flume. Flow depths were measured to compare the initial with the abraded state.
Furthermore, turbulence measurements using 2D-laser Doppler anemometry technique were performed to obtain the mean and turbulence flow characteristics. This paper describes results of these measurements focusing on the streamwise and vertical flow velocities, turbulence intensities and Reynolds shear stress.
Reservoir sedimentation is increasingly affecting the majority of reservoirs all over the world. As many dams are more than 50 years of age, this problem is becoming more and more seriou403s nowadays. Reservoir sedimentation leads to various severe problems such as a decisive decrease of the active reservoir volume leading to both loss of energy production and water available for water supply and irrigation. These problems will intensify in the very next future, because sediment supply tends to increase due to climate change. Therefore coun-termeasures have to be developed. They can be divided into the three main categories sediment yield reduction, sediment routing and sediment removal. This paper focuses on sediment routing by means of sediment bypass tunnels. Sediment bypass tunnels are an effective measure to stop or at least decrease the reservoir sedimentation process. By routing the sediments around the reservoir into the tailwater in case of flood events sediment accumulation of both bed load and suspended load is reduced significantly. However, the number of sediment bypass tunnels in the world is limited primarily due to high investment and above all maintenance costs. The state-of-the-art design criteria of constructing bypass tunnels are summarized herein; major problems such as tunnel invert abrasion are discussed. The need for further research regarding sediment transport in bypass tunnels and invert abrasion is highlighted.
Entlandung des Stausees Solis mit Hilfe eines Geschiebeumleitstollens – hydraulische Modellversuche
(2009)
Das Reservoir der Talsperre Solis in Graubünden wurde 1986 vom Elektrizitätswerk der Stadt Zürich (ewz) in Betrieb genommen. Bei Hochwasserereignissen werden grosse Sedimentmengen in den Stausee transportiert. Über 25 % des ursprünglichen Reservoirvolumens sind bereits verlandet. Aus diesem Grund plant ewz den Bau eines Geschiebeumleitstollens, der das bei Hochwasser ankommende Sediment um die Talsperre herum in Richtung Unterwasser leitet. Die Versuchsanstalt für Wasserbau, Hydrologie und Glaziologie (VAW) der ETH Zürich untersucht und optimiert in einem hydraulischen Modell den projektierten Umleitstollen. Bei Hochwasser wird der Stausee auf den minimalen Betriebswasserspiegel abgesenkt, der Verlandungskörper liegt grösstenteils frei, das Sediment erodiert. Mit Hilfe einer Leitkonstruktion wird die Strömung in Richtung Einlaufbauwerk des Stollens gelenkt und der Abfluss sowie das Geschiebe durch diesen geleitet. Bei Abflüssen, die die Ausbaukapazität des Stollens (HQ5) überschreiten, wird die überschüssige Strömung in den vorderen Bereich des Sees in Richtung Grundablass abgeführt. Das Geschiebe wird dennoch nahezu vollständig in den Stollen eingeleitet. Bei Hochwasser mit Schwemmholzaufkommen wird mit Hilfe einer Tauchwand sowie einer Teilablleitung des Hochwasserabflusses in den vorderen Seebereich verhindert, dass Schwemmholz in den Umleitstollen
eingezogen wird.
The Solis reservoir is located in the Alps in Grisons, Switzerland and is operated by the electric power company of Zurich (ewz). Since its construction in 1986, high sediment input during flood events has led to major aggradations in the reservoir. Up to date, nearly half of the original reservoir volume has been filled with sediments from upstream mountain torrents. The deltaic deposition starts extending into the active water volume. Therefore, ewz plans a sediment bypass tunnel to flush the incoming bedload around the dam to the downstream reach. In a first step the reservoir level during flood events is lowered to the minimum operation level. The delta is subjected to free surface flow and the bedload is transported over the delta and deposited further downstream. This sediment relocation decreases the delta volume within the active storage. During further flood events, the incoming sediment is led to the bypass tunnel intake using a guiding structure and flushed through the tunnel. If the flood exceeds the capacity of the bypass tunnel, the surplus flow passes the tunnel intake towards the bottom outlets with the bedload still being flushed through the tunnel. A skimming wall located upstream from the tunnel intake prevents driftwood blocking by leading it to the reservoir front where it can be safely removed. Both the sediment relocation due to water level drawdown and the flushing through the bypass tunnel are investigated and optimized in a hydraulic model at the Laboratory of Hydraulics, Hydrology and Glaciology (VAW) of ETH Zurich. Additionally, the sediment relocation process in the model is compared with a relocation test in the prototype.
Reservoir sedimentation, a serious problem affecting the majority of reservoirs worldwide, was not systematically accounted for in the past. After 50 years of operation, a constantly decreasing reservoir volume becomes currently a serious challenge for reservoir owners, against which countermeasures have to be developed. This research focuses on sediment routing using a bypass tunnel to convey sediments past a dam.
By transporting sediments into the tailwater past a dam, their accumulation in the reservoir is reduced significantly. However, the global number of sediment bypass tunnels is limited primarily due to high investment and maintenance cost. The main problem of all bypass tunnels is the massive invert abrasion due to high flow velocities combined with high sediment transport rates. Therefore, VAW started two research projects to counter this problem. The main goal of the first project Layout and design of sediment bypass tunnels is to investigate the invert abrasion process by conducting hydraulic laboratory tests and to establish general design criteria for optimal flow conditions in which both sediment depositions in the tunnel are avoided and the resulting abrasion damages are kept at a minimum. The second project Optimizing hydroabrasive-resistant materials at sediment bypass tunnels and hydraulic structures investigates the hydraulic resistance of different tunnel invert materials, such as high performance concrete or cast basalt plates in prototype tests at the Solis bypass tunnel. The sediment transport measurement technique used in this project was optimized during preliminary model tests.
Sedimentumleitstollen leiten die sedimentreichen Hochwasserspitzen um die Tal-sperre herum in den Unterlauf des Flusses und verhindern so eine fortschreitende Verlandung des Stauraums. Aufgrund der hohen Fließgeschwindigkeiten und gro-ßen Sedimentfrachten in Umleitstollen weisen diese starke Verschleißerscheinun-gen auf, die zu hohen Unterhaltskosten führen. Es gibt verschiedene Konzepte um diesem Problem entgegen zu wirken. Einerseits kann der Umleitstollen hydrau-lisch optimiert werden, um die Belastung auf die Sohle zu minimieren. Auf der anderen Seite kann der Widerstand der Stollensohle verbessert werden. An der Versuchsanstalt für Wasserbau, Hydrologie und Glaziologie (VAW) der ETH Zü-rich werden zur Zeit zwei Forschungsarbeiten durchgeführt, die sich diesen zwei Aspekten widmen. In großskaligen Laborversuchen erfolgt eine systematische Untersuchung und Optimierung der maßgebenden Parameter wie Fortbewegungs-art des Sediments und Abrasionstiefe der Stollensohle. Anhand von Prototypver-suchen im neu errichteten Sedimentumleitstollen Solis in Graubünden (Schweiz) werden die Zusammenhänge zwischen Beanspruchung, Materialeigenschaften und Abrasion im Prototyp ermittelt. Darauf basierend können Empfehlungen be-züglich Materialwahl, konstruktiver Durchbildung und Dimensionierung abgege-ben und so zu einer nachhaltigen und wirtschaftlichen Wasserbewirtschaftung in Stauseen beigetragen werden.
Reservoir sedimentation is an increasing problem affecting the majority of reservoirs both in Switzerland and worldwide. As many dams are more than 50 years of age, this problem is becoming more and more serious nowadays. Res-ervoir sedimentation leads to various severe problems such as a decisive de-crease of the active reservoir volume leading to both loss of energy production and water available for water supply and irrigation. These problems will intensify in the near future, because sediment supply tends to increase due to climate change. Therefore, countermeasures have to be developed. They can be divided into the three main categories sediment yield reduction, sediment routing and sediment removal. This paper focuses on the sediment routing using sediment bypass tunnels. Sediment bypass tunnels are an effective means to decrease the reservoir sedimentation process. By routing the sediments around the reservoir into the tailwater, sediment accumulation is reduced significantly. However, the number of sediment bypass tunnels in the world is limited primarily due to high investment and maintenance costs. The main problem of all bypass tunnels is the invert abrasion due to high velocities in combination with high sediment transport. Three Swiss bypass tunnel examples suffering invert abrasion are presented in this paper. Furthermore, VAW started a research project to investigate the invert abrasion process by conducting hydraulic scale tests in the laboratory. The goal of this research project is to establish general design criteria for optimal flow con-ditions where both sediment depositions in the tunnel are avoided and the result-ing abrasion damages are kept at a minimum.
This paper deals with an experimental investigation of the mean and turbulence characteristics of supercritical quasi-uniform and gradually varied open-channel flows over a transitional rough bed. These conditions are typical for sediment bypass tunnels. The results show that the log-law holds well in the inner region across the channel. The roughness shifts the velocity profiles downward by an amount of ΔU+. The velocity-dip phenomenon and strong secondary currents exist in the channel for narrow open-channel flow. These currents cause the Reynolds shear stress distributions to deviate from the linear distribution and an undulation on the transversal distribution of the bed shear stress, which matches with the bed abrasion pattern. The streamwise turbulence intensity profiles deviate from the semi-empirical universal function whereas the vertical turbulence intensity profiles fit well with it only at the centerline of the channel. A strong wall effect exists on the turbulence intensities in the outer region.
Single glass sphere motion recordings were conducted in a transitional-rough bed open channel at steady and highly supercritical flow similar to hydraulic conditions in sediment bypass tunnels. A high speed camera with a maximum resolution of 2,560 × 2,160 pixels was used to record the movement of bedload particles with diameters of D = 5.3, 10.3 and 17.5 mm. An in-house developed Particle Tracking Velocimetry (PTV) program was used to determine the transport mode and velocities of each particle for a wide range of Froude numbers up to Fo = 6. The relative roughness defined as the ratio of the bed roughness height ks to the water depth h varied from ks/h = 0.02–0.03. Particles were observed to move in rolling and saltation modes depending on the Shields number. The particle velocity shows a linearly increasing relationship with both friction velocity and Froude number nearly independent on the particle diameter. A linear relationship was also found between rolling and saltating particle velocities indicating that particle velocity does not depend on the transport mode in the range of the investigated hydraulic conditions. Scaling of particle velocity with the wave celerity plotted as a function of the Froude number adequately merged external data sets with the present data. As a consequence, a linear fit for a large Froude number range was obtained.
Worldwide, a large number of reservoirs impounded by dams are rapidly filling up with sediments. As on a global level the loss of reservoir volume due to sedimentation increases faster than the creation of new storage volume, the sustainability of reservoirs may be questioned if no countermeasures are taken. This paper gives an overview of the amount and the processes of reservoir sedimentation and its impact on dams and reservoirs. Furthermore, sediment bypass tunnels as a countermeasure for small to medium sized reservoirs are discussed with their pros and cons. The issue of hydroabrasion is highlighted, and the main design features to be applied for sediment bypass tunnels are given.
Supercritical sediment-laden open channel flows occur in many hydraulic structures including dam outlets, weirs, and bypass tunnels. Due to high flow velocities and sediment flux severe problems such as erosion and abrasion damages are expected in these structures (Jacobs et al., 2001). Sediment bypass tunnels (SBT), as an effective measure to decrease reservoir sedimentation by bypassing sediments during floods, are exceptionally prone to high abrasion causing significant annual maintenance cost (Sumi et al., 2004; Auel and Boes, 2011). The Laboratory of Hydraulics, Hydrology and Glaciology (VAW) of ETH Zurich conducted a laboratory study to counteract these negative effects (Auel, 2014). The main goals of the project were to analyze the fundamental physical processes in supercritical flows as present in SBTs by investigating the mean and turbulence flow characteristics (Auel et al., 2014a), particle motion (Auel et al., 2014b; 2015b), and abrasion development caused by transported sediment. Besides new insights into the three listed topics, paramount interest is given to their inter-relations and the development of an easily applicable abrasion prediction model (Auel et al., 2015a). This paper presents selected results on the second topic, i.e. the analysis of saltation trajectories of single coarse particles in supercritical flow.
The Solis dam was built in 1986 by the Electric Power Company of Zurich (ewz). Ever since the construction, large amounts of sediments accumulated in the reservoir and led to severe sediment aggradation. As a consequence, the storage volume was reduced by about 50% till 2012 causing loss of energy production. Additionally, in the near future sediments may have caused severe damage at the dam due to blockage of the bottom outlets. Therefore, in 2011 and 2012 a sediment bypass tunnel was realized in order to redirect the incoming sediments into the tailwater to inhibit sediment aggradation. Since its inauguration, the tunnel was operated four times including a 100-year flood event in August 2014. First operational experiences are described herein.