Wittrock, Ulrich
Refine
Year
Publication Type
- Article (18)
- Conference Proceeding (18)
- Contribution to a Periodical (2)
- Book (1)
- Part of a Book (1)
- Part of Periodical (1)
Language
- English (33)
- German (6)
- Multiple languages (2)
Keywords
- adaptive optics (3)
- deformable mirror (3)
- active optics (2)
- active optics, adaptive optics, sharpness metrics, aberration compensation, algorithm design (2)
- deformable mirrors (2)
- laser machining (2)
- space optics (2)
- space telescopes (2)
- Active or adaptive optics (1)
- Deformable mirror, adaptive mirror, unimorph mirror, high-power laser (1)
Faculty
Adaptive laser resonators with deformable MOEMS mirrors under closed-loop control are discussed and experimental results are presented. The requirements for deformable mirrors and for closed-loop control systems of these mirrors are analyzed. Several deformable mirrors have been characterized and the results are presented. Currently available membrane mirrors deform under laser load and need further development before they can be used for aberration correction of solid state lasers above some tens of Watts. Nevertheless, the results are encouraging and the requirements are within reach of currently available technology. Finally, we demonstrate an Nd.YVO4-laser with a closed-loop adaptive resonator and more than 6 W of output power. The closed-loop system was able to compensate artificially introduced aberrations from a phase plate.
The spatially varying intensity in a standing wave resonator leads to spatial hole burning in the gain medium of a laser. The spatial hole burning changes the gain of different longitudinal modes and can thus determine the optical spectrum of the laser. We simulate this longitudinal mode competition in standing wave resonators of thin-disk lasers. The resulting optical spectra of the laser are compared to measured optical spectra. We examine two types of resonators: I-resonators and V-resonators with different angles of incidence. In V-resonators, the non-normal incidence of the laser beam on the disk lifts the degeneracy of the polarization. Experiments show that the slight gain advantage for the p-polarization does not lead to polarized emission. For both types of resonators, the measured spectra are in good agreement with the simulated ones. The simulations allow to study the influence of spectral intra-cavity losses on the optical spectrum of a thin-disk laser.
We present, to the best of our knowledge, the first intracavity pumped Yb:YAG thin-disk laser. It operates at 1050.7 nm with a quantum defect of just 1.74% due to pumping at 1032.4 nm. Low absorption of the pump light at the pump wavelength of 1032.4 nm is compensated for by placing the disk inside the resonator of another Yb:YAG thin-disk laser which is diode-pumped at 940 nm. The intra-cavity pumped laser has an output power of 10.3 W and a slope efficiency of 8.3%
We present a novel pump concept that should lead to single-frequency operation of thin-disk lasers without the need for etalons or other spectral filters. The single-frequency operation is due to matching the standing wave pattern of partially coherent pump light to the standing wave pattern of the laser light inside the disk. The output power and the optical efficiency of our novel pump concept are compared with conventional pumping. The feasibility of our pump concept was shown in previous experiments.
The actuator pattern of an adaptive mirror determines the amplitudes and the fidelities of the mirror deformations that can be achieved. In this study, we analyze and compare different electrode patterns of piezoelectric unimorph deformable mirrors using a numerical finite element model. The analysis allows us to determine the optimum actuator pattern, and it is also applicable to bimorph mirrors. The model is verified by comparing its predictions with experimental results of our prototype of a novel unimorph deformable mirror.
Over the past 5 years we have developed a new type of unimorph deformable mirror. The main advantages of this mirror technology are · very low surface scattering due to the use of superpolished glass · excellent coatings, even suitable for high power lasers, can be applied · active diameter of the mirrors can be between 10 mm and 100 mm · large strokes can be achieved even for small mirror diameters · integrated monolithic tip/tilt functionality based on a spiral arm design We have modeled these mirrors by analytical models as well as by the finite element method. This allows us to quickly design new mirrors tailored to specific applications. One example is a mirror for laser applications that has a diameter of 10 mm and can achieve a stroke in defocus mode of 5 μm. The stroke for these mirrors scales as the square of the mirror diameter, meaning that we can achieve, for example, a stroke of 125 μm for a mirror of 50 mm diameter. We will present design criteria and tradeoffs for these mirrors. We characterize our mirrors by the maximum stroke they can deliver for various Zernike modes, under the boundary condition that the Zernike mode has to be created with a certain fidelity, usually defined by the Maréchal criterion.