Refine
Year of publication
- 2018 (6) (remove)
Document Type
Language
- English (6)
Is part of the Bibliography
- no (6)
Institute
Bedload transport and hydro-abrasive erosion at steep bedrock rivers and hydraulic structures
(2018)
In this paper typical bypass efficiencies of sediment bypass tunnels (SBTs) used to counter reservoir sedimentation are described, distinguishing between two layouts of the tunnel intake. It results that SBTs are an effective measure to reduce the sedimentation of dam reservoirs, particularly of type (A) with intake at the reservoir head. The hydroabrasive wear of tunnel inverts is significant and
has to be mitigated by using adequate invert liners. The invert abrasion can be estimated based on an abrasion model where a correct input value of the bed material resistance coefficient is paramount to limit model uncertainties. Based on abrasion measurements at prototype SBTs typical values of the material resistance coefficient are recommended for high-strength concrete, natural stones and steel liners. The field experiences gathered so far and the comparison of various invert materials suggest granite pavers as a promising lining material for severe abrasion conditions.
Without adequate measures, reservoirs are not sustainable, neither the
reservoir itself due to continuous sedimentation, nor the downstream ecosystem due to altered sediment continuity. Appropriate actions are inevitable and require a systematic sedimentation management. Sediment bypassing constitutes one effective strategy that routes sediment load around reservoirs during floods. A sediment bypass system has the advantage that only newly entrained sediment is diverted from the upstream to the downstream reach thereby re-establishing sediment connectivity. Hence, such a system contributes to a sustainable water resources management while taking the downstream environment into consideration. This paper gives a state-of-the-art overview
encompassing design, bypass efficiency, hydraulics, challenges due to abrasion, positive effects on both downstream morphology and ecology, and makes design recommendations.
This paper describes the design of the new tunnel invert lining of the 9-foot tunnel at Mud Mountain Dam, Washington, USA. The tunnel diverts all bed load sediments into the tailwater. Major invert abrasion has been observed in the existing steel lining. The new invert design consists of 0.59 m2 and 0.79 m2 granite blocks that are 0.25 m thick and placed tightly together along the tunnel. Stability analysis showed factors of safety ranging from 1.2 to 2.6 against uplift. This will be achieved with strip drains placed in the bedding material along the tunnel. A service-design-life analysis was performed using abrasion prediction modelling.
This model was based on abrasion measurement data acquired from granite field tests at Pfaffensprung sediment bypass tunnel, Switzerland. The estimated annual abrasion depths for the granite were approximately 0.50 mm/year for average sediment transport conditions.
To achieve the sustainable use of dams, the development of methods for sediment management in reservoirs is required. One such method includes the use of Sediment Bypass Tunnels (SBTs) to divert sediment around a dam, thereby preventing sedimentation in the reservoir. However, SBTs are prone to severe invert abrasion caused by the high sediment flux. Therefore, it is necessary to establish a measurement system of the sediment transport rate in these tunnels. One system to measure sediment transport in rivers is the Swiss plate geophone, which can register plate vibrations caused by particle impact. In Japan, the Japanese pipe microphone is used, and sediment transport is measured based on the sound emitted by the particle impact. In this study an attempt was made to optimize the advantages of both systems by fixing a microphone and an acceleration sensor to a steel plate. The results of calibration experiments with this new system are presented and compared with the existing methods. It was found that the acceleration sensor can detect sediment particles larger than 2 mm in diameter. Moreover, a new parameter, referred to as the detection rate, was introduced to describe the correlation between the actual amount of sediment and the registered output. Finally, two parameters - the saturation rate and hit rate - are introduced and exhibit strong correlation with the detection rate.
Abrasion in a concrete-lined sediment bypass tunnel is estimated using a Japanese state-of-the-art prediction model and validated by measured invert abrasion data at Asahi Reservoir, Japan. The model is described in detail, certain shortcomings are disclosed, and a revised version is proposed. The model consists of a kinetic energy term accounting for the impact by saltating particles, and a friction work term accounting for the grinding stress. It is found that the latter term yields concrete abrasion values being consistently a multiple compared to its kinetic term contradicting other research. Based on that, and a possible particle impact angle inconsistency, it is proposed to omit the friction work term. It is shown that the calculated abrasion is overestimated by 138% on average compared with that measured, if both terms are accounted for. However, promising results are obtained with only 30% overestimation by neglecting the friction work term.