Refine
Publication Type
- Article (26)
- Conference Proceeding (2)
- Part of a Book (1)
Keywords
- Additive manufacturing (1)
- High-entropy alloy (1)
- Laser metal deposition (1)
- Laser shock peeningFemtosecond laserNiTi alloyCorrosion behaviorLaser surface treatment (1)
- Powder blend (1)
- Refractory (1)
- laser mode locking; polymerisation; optical waveguides; high-speed optical techniques; two-photon processes; optical pulse compression; optical saturable absorption; integrated optics; semiconductor lasers (1)
- laser nitriding; wear resistance; NiTi alloy; roughness; microhardness (1)
- laser shock peeningfemtosecond laserNiTi alloymicrohardness (1)
Two-photon polymerization with diode lasers emitting ultrashort pulses with high repetition rate
(2020)
In this Letter, we investigate the resolution of two-photon polymerization (2PP) with an amplified mode-locked external cavity diode laser with adjustable pulse length and a high repetition rate. The experimental results are analyzed with a newly developed 2PP model. Even with low pulse peak intensity, the produced structural dimensions are comparable to those generated by traditional 2PP laser sources. Thus, we show that a compact monolithic picosecond laser diode without amplification and with a repetition rate in the GHz regime can also be applied for 2PP. These results show the high application potential of compact mode-locked diode lasers for low-cost and compact 2PP systems.
The laser nitriding was performed in nitrogen gas at room temperature (20 °C) and low temperature (−190 °C) by a low power fiber laser to modify the wear and abrasion resistance of NiTi alloy. The surface roughness and element composition were analyzed by roughness device and energy-dispersive X-ray spectroscopy respectively. The results of roughness show that laser treatment can change the surface roughness due to the laser remelting. The effect of laser nitriding on the microhardness, friction coefficient, and worn scars of NiTi alloy was also studied, which shows that the microhardness of the NiTi alloy increases after laser nitriding. The optical microscope and scanning electron microscope were used to characterize the surface of NiTi alloy after wear testing to observe the microstructure of worn scars. The results show that the laser nitriding with different parameters can induce a nitride layer with different thicknesses and the higher energy deposition is the key factor for the formation of the nitride layer, which can decrease the friction coefficient and reduce wear loss during the application of NiTi alloy. The improvement of wear resistance can be attributed to the hard nitriding layer.
Synthesis of Magnetic Nanoparticles by Ultrashort Pulsed Laser Ablation of Iron in Different Liquids
(2017)
This research paper presents the attempt at ultrashort pulsed laser shock peening with absence of absorptive layer and confining medium which could enhance surface microhardness and the abrasion property of NiTi shape memory alloy. The average roughness values of NiTi specimen were measured on the surface, because the roughness would affect the friction resistance. The microhardness and Young's modulus were investigated at different position of single laser spot by nanoindentation technique. The pin-on-plate sliding abrasion testing were performed with different load-force (0.5 N and 2 N) for different testing time. Results showed that ultrashort pulsed laser shock peening treatment would cause a significant improvement on friction coefficient and abrasion property, which was attributed to the change of surface modification, such as roughness, microhardness, microstructure and titanium oxide layer …
Studies on ultra-short pulsed laser shock peening of stainless-steel in different confinement media
(2020)
We investigate the role of liquid confinement media on ultra-short pulsed Laser Shock Peening (LSP). The LSP of stainless-steel 316 and 316 L was studied using Ti: Sapphire laser pulses of about 2 ps duration, maximum energy of about 1 mJ and pulse repetition rate of 5 kHz in different liquid confinement media of Ethanol, Deionized water and separate aqueous solutions of NaCl and Glycerol. It is found that the laser fluence and/or energy attenuating mechanisms like self-focusing, filamentation, plasma breakdown in the confinement media are less significant with ps laser pulses than those with sub-ps or fs pulse durations. It is shown that the resulting surface hardness of the peened steel as a function of laser fluence depends significantly on the confinement media and the relative increase in the hardness increases monotonically with the acoustic impedance of the liquid of the confinement medium used during …
This paper describes how two-photon polymerization was used to generate biomimetic nanostructures with angle-insensitive coloration inspired by the blue butterflies of Morpho. Less angle dependence was achieved by engineering the structures with a certain degree of disorder, which delimited them from classical photonic crystals. Variations in the processing parameters enabled the color hue to be controlled. In this context, blue, green, yellow, and brown structures were demonstrated. Reflection spectra of the structures were simulated and studied experimentally in a broad range of incident angles. Additionally, a molding technique was performed as a potential scale-up strategy. The application of such biomimetic structures is discussed.
In this work, the authors report on investigations of two-photon lithography of positive photoresist. The dependency of the pattern linewidth on variation in the processing parameters, like the laser patterning velocity or power of the femtosecond laser oscillator, is presented. The influence of the scan velocity between 0.38 and 1.90 mm/s on the resolution is discussed for a layer thickness of 3.5 μm. By using a commercial positive photoresist, an aspect ratio of 5 has been realized for grid structures and the qualities of the produced structures are discussed.
In this Letter, the authors present the construction of three-dimensional microstructures by two-photon polymerisation induced by ultrashort pulses of a mode-locked diode laser. The ultrafast light source is based on a diode laser with segmented metallisation to realise a waveguide integrated saturable absorber. It is subsequently amplified and compressed resulting in ultrashort laser pulses of 440 fs length and average output power of 160 mW at a fundamental repetition rate of 383.1 MHz. These pulses are coupled into a customised two-photon polymerisation setup. A series of suspended lines were fabricated between support cuboids for testing the process behaviour. A 3D structure with complex features was polymerised to demonstrate the high potential for mode-locked diode lasers in the field of direct laser writing.
The experiment study presents the influence of femtosecond laser shock peening (FsLSP) without a protective layer in the air on the surface hardness and surface mechanical property of NiTi shape memory alloy. Femtosecond laser shock peening is a new possibility of direct laser ablation without any protective layer under atmospheric conditions, which can produce intense shock waves with low pulse energy in the air. The average surface roughness values of the NiTi alloy samples were measured, because the surface roughness may affect its friction resistance. The results showed that the surface roughness of NiTi increased after femtosecond laser shock peening treatment. In comparison with the initial state, the coefficient of friction decreased and surface microhardness increased after femtosecond laser shock peening treatment with different FsLSP parameters. This improvement of wear properties may be attributed to the enhancement of surface microhardness and surface titanium oxide layer induced by the shock wave and laser ablation during FsLSP treatment.
High strength steel has been used in the aviation industry and automotive body structural applications to reduce its mass through a reduction in thickness. Therefore, it is very important to enhance its mechanical property, such as microhardness. In the present research, the high strength steel samples were treated by laser shock peening (LSP) with different laser pulse energy and laser pulse width. The microhardness and residual stress were measured to compare the difference between laser energy of 3 J with 10 ns and 5 J with 20 ns. The results in the study show that the surface LSP treatment can increase the microhardness and the compressive residual stress can be found when the samples were tested by hole drilling testing.
Progress in materials development is often paced by the time required to produce and evaluate a large number of alloys with different chemical compositions. This applies especially to refractory high-entropy alloys (RHEAs), which are difficult to synthesize and process by conventional methods. To evaluate a possible way to accelerate the process, high-throughput laser metal deposition was used in this work to prepare a quinary RHEA, TiZrNbHfTa, as well as its quaternary and ternary subsystems by in-situ alloying of elemental powders. Compositionally graded variants of the quinary RHEA were also analyzed. Our results show that the influence of various parameters such as powder shape and purity, alloy composition, and especially the solidification range, on the processability, microstructure, porosity, and mechanical properties can be investigated rapidly. The strength of these alloys was mainly affected by the oxygen and nitrogen contents of the starting powders, while substitutional solid solution strengthening played a minor role.
Laser shock peening with a femtosecond laser system was presented in this research work. The NiTi shape memory alloy was processed by the femtosecond laser shock peening (FsLSP) treatment without a protective layer in the air. Femtosecond laser shock peening is a new surface technology, which can induce an intense shock wave with low single laser pulse energy under atmospheric conditions. The surface topography, roughness, microhardness, and wear resistance were measured on the surface of NiTi alloy before and after femtosecond laser peening treatment. The results showed that the surface roughness and microhardness could be increased after femtosecond laser shock peening, which may be due to the laser ablation and micro-plastic deformation induced by the shock wave. The wear property of NiTi alloy was improved, which may be attributed to the FsLSPed surface texturing and …
Laser shock peening with femtosecond laser was used to improve the corrosion resistance of biomedical NiTi alloy without protective coating in the air environment. The energy dispersive X-ray analysis (EDX) and X-ray diffraction (XRD) based analysis showed that the laser ablation could produce titanium oxide layer and femtosecond laser shock peening (FsLSP) can generate residual stress in the surface layer of NiTi alloy. The FsLSP improved the corrosion resistance of NiTi in 3.5% NaCl solution and Hank’s solution and also prevented the formation of corrosion cracks and pits during corrosion testing. The reasons for the improvement of corrosion behavior may be the generation of residual stress and titanium oxide film during the laser surface treatment.
Laser shock peening is a new and important surface treatment technique that can enhance the mechanical properties of metal materials. Normally, the nanosecond laser with pulse-width between 5 ns and 20 ns is used to induce a high-pressure shock wave that can generate plastic deformation in the top layer of metals. The femtosecond laser shock peening in the air has been studied recently, which can induce higher pressure shock wave than that of traditional nanosecond laser shock peening in a very short time. The NiTi alloy is processed by femtosecond laser shock peening, then a nanoindentation device is used to measure its surface hardness and residual stress. The hardness results of NiTi alloy before and after treatment show that the femtosecond laser shock peening can increase the hardness of NiTi alloy, which also shows that the femtosecond laser can be used to perform laser shock peening on NiTi alloy without coating.