TY - JOUR A1 - Vennemann, Peter T1 - Zukunft der Stromspeicherung in Pumpspeicherkraftwerken T1 - Future of Energy-Storage with Pumped Hydro Power JF - Deutsches Ingenieurs-Blatt N2 - Mit wenigen Ausnahmen wird im elektrischen Versorgungssystem die Pumpspeichertechnik zur Pufferung größerer Abweichungen zwischen momentanem Stromverbrauch und -erzeugung und zur zeitlichen Verschiebung von Lasten eingesetzt. Erste großtechnische Anlagen wurden bereits Ende der zwanziger Jahre des letzten Jahrhunderts in Deutschland gebaut, um die Auslastung thermischer Kraftwerke gleichmäßiger zu ermöglichen. Pumpspeicherwerke bieten sich somit als Referenztechnologie an, mit der sich neue Entwicklungen messen müssen. Ein Überblick. N2 - Pumped hydro power is the first choice for buffering larger deviations between supply and demand of electricity. In Germany, first plants were build in the late nineteen-twenties. Pumped hydro power can be used as a reference technique for emerging technologies for electricity storage. The article gives an introduction into the pumped hydro power technology. KW - Energiewirtschaft KW - Energieversorgung KW - Wasserkraft KW - Pumpspeicher Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:836-opus-6954 VL - 2014 IS - 3 ER - TY - JOUR A1 - Falter, Bernhard A1 - Alberding, Mechthild T1 - Zeitabhängiges Beulverhalten von U-Linern aus PE-HD T1 - Time-dependent buckling behaviour of HDPE U-liners JF - 3R international, Heft 9, 1997, Seite 534-541 N2 - Im Rahmen eines USA-Praxissemesters der erstgenannten Autorin an der Tulane University in New Orleans wurden im Jahr 1995 in Zusammenarbeit mit Pipe Liners, Inc. Außendruckversuche an PE-HD-Linern durchgeführt. Bei diesen Versuchen sollte der maximale Beuldruck unter Variation von Randbedingungen des Liners im Altrohr (hier: Längsversatz und Ovalisierung) ermittelt werden. Außerdem war die Ermittlung des Zeitstandverhaltens der mit konstantem Außendruck beaufschlagten Versuchskörper ein wichtiges Versuchsziel. Die experimentellen Ergebnisse werden unter Verwendung der vom Zweitverfasser entwickelten nichtlinearen Theorie ausgewertet. N2 - ln the context of a practical semester spent in the USA by the first of the above-mentioned authors at Tulane University, New Orleans, La., external pressure tests were performed on HDPE liners in cooperation with Pipe Liners, lnc., during 1995. The objective of these tests was the determination of the maximum buckling pressure at various liner conditions in the host pipe (in this case: longitudinal misalignment and ovalization). ln addition, the determination of the creep resistance behaviour of the test objects when exposed to a constant external pressure was another important test target. The experimental results are evaluated using the non-linear theory developed by the second author. KW - Außendruckversuche KW - PE-HD Liner KW - Liner KW - Beuldruck KW - Ovalisierung KW - nichtlineare Theorie KW - Tulane University KW - Pipe Liners KW - Zeitstandverhalten KW - external pressure tests KW - HDPE liners KW - liner KW - bulging pressure KW - ovalization KW - non-linear theory KW - Pipe Liners KW - creep resistance behaviour Y1 - 1997 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:836-opus-348 VL - 1997 IS - 9 SP - 534 EP - 541 PB - Oldenbourg Industrieverlag ER - TY - JOUR A1 - Gellenbeck, Klaus T1 - Wertstofftonne in der Praxis - Projekte, Stoffströme, Kosten JF - Müll und Abfall N2 - Ausgelöst durch das neue Kreislaufwirtschaftsgesetz werden derzeit in zahlreichen Gebietskörperschaften Maßnahmen zur Erweiterung der Wertstofferfassung bis hin zur Erarbeitung einer Wertstoffstrategie unternommen. Der Beitrag gibt einen Überblick über die Ausgestaltung in der Praxis sowie die bisherigen Erfahrungen, die durch die Begleitung vieler Modellversuche ermittelt wurden. Y1 - 2013 U6 - http://dx.doi.org/10.25974/fhms-704 VL - 2013 IS - 9 PB - Erich Schmidt Verlag ER - TY - JOUR A1 - Rausch, Peter A1 - Verpoort, Sven A1 - Wittrock, Ulrich T1 - Unimorph deformable mirror for space telescopes: environmental testing JF - Opt. Expr. N2 - We have developed and manufactured a unimorph deformable mirror for space telescopes based on piezoelectric actuation. The mirror features 44 actuators, has an aperture of 50 mm, and is designed to reproduce low-order Zernike modes with a stroke of several tens of µm. We assessed the space compliance by operating the mirror in thermal vacuum, and exposing it to random and sinusoidal vibrations, as well as to ionizing irradiation. Additionally, the operational life time and the laser power handling capability were tested. The mirror was successfully operated in thermal vacuum at 100 K. We report on the conducted tests and the methods used to evaluate the mirror´s performance, and discuss the compliance with the demanded requirements KW - active or adaptive optics KW - telescopes thermal effects vibration analysis KW - radiation KW - space optics KW - space instrumentation Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:836-opus-8530 VL - 24 SP - 1528 EP - 1542 ER - TY - JOUR A1 - Rausch, Peter A1 - Verpoort, Sven A1 - Wittrock, Ulrich T1 - Unimorph deformable mirror for space telescopes: design and manufacturing JF - Opt. Expr. N2 - Large space telescopes made of deployable and lightweight structures suffer from aberrations caused by thermal deformations, gravitational release, and alignment errors which occur during the deployment procedure. An active optics system would allow on-site correction of wave-front errors, and ease the requirements on thermal and mechanical stability of the optical train. In the course of a project funded by the European Space Agency we have developed and manufactured a unimorph deformable mirror based on piezoelectric actuation. The mirror is able to work in space environment and is designed to correct for large aberrations of low order with high surface fidelity. This paper discusses design, manufacturing and performance results of the deformable mirror. KW - Active or adaptive optics KW - Telescopes KW - Space optics KW - Space instrumentation Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:836-opus-8227 VL - 23 SP - 19469 EP - 19477 ER - TY - JOUR A1 - Gellenbeck, Klaus T1 - TOP-Kennzahlen zur Standortbestimmung für die Abfallwirtschaft und Stadtreinigung - 8. Durchgang zum VKU-Benchmarking startet im Frühjahr 2012 JF - VKS-News N2 - Die anhaltende Diskussion um Wirtschaftlichkeit, Leistungsfähigkeit und Qualität der Dienstleistung veranlasst zunehmend mehr Abfallwirtschaft- und Stadtreinigungsbetreibe sich mit der Frage auseinanderzusetzen, " Wo steht mein Betreib im Vergleich zu anderen und wie muss ich mich als Betrieb positionieren?". Erst Antworten hierzu kann u. A. auch eine Teilnahme an einem brancheninternen Benchmarking-Verfahren liefern. KW - Kennzahl KW - Abfallwirtschaft KW - Stadtreinigung Y1 - 2012 U6 - http://dx.doi.org/10.25974/fhms-687 PB - VKU-Verlag ET - 161 ER - TY - JOUR A1 - Falter, Bernhard T1 - Standsicherheitsnachweis an Sanierungssystemen für Abwasserkanäle mit unverankerten Linern T1 - Structural analysis for renovation systems of sewers with non-anchored liners JF - 3R international N2 - Schadhafte Abwasserkanäle und -leitungen können durch Einziehen eines flexiblen Liners oder durch Teilauskleidung mit Platten saniert werden. Der Ringraum zwischen Rohr und Liner wird häufig mit Dämmer verfüllt. Die Standsicherheit muss für die Lebensdauer des sanierten Bauwerks unter den während der Sanierungsarbeiten und beim Betrieb des Abwasserkanals herrschenden Bedingungen gewährleistet sein. Das bedeutet, dass konservative Annahmen bezüglich des System- und Belastungsverhaltens zu treffen sind. Für einige wichtige Lastfälle (hydrostatischer Druck mit Auftrieb, Eigenlasten, Temperaturänderungen usw.) werden Lösungsansätze diskutiert und Durchschlagbeiwerte alpha D angegeben. Von besonderer Bedeutung für die Sicherheitsnachweise ist der richtige Ansatz der Vorverformungen: Sie müssen sowohl die Verformungen des Kanals repräsentieren als auch stabilitätstheoretischen Erkenntnissen entsprechen. N2 - Defect sewers can be repaired by drawing in flexible liners or by lining parts of the circumference. The gap between pipe and liner is usually grouted. The structural safety of the renovated sewer must be ensured during the construction works and under long-term service conditions. This means, that conservative assumptions for the system and the load behaviour must be introduced into the analysis. For some important load cases (hydrostatic pressure with buoyancy, dead loads, temperature change etc.) solution methods are discussed and snap through coefficients alpha D are presented. A true statement of the imperfections is very important far the safety analysis: The imperfections have to represent the deflections of the sewer and must be in accordance with the stability theory. KW - Rohrleitungsstatik KW - Sanierung KW - Liner KW - Durchschlaglasten KW - Temperaturerhöhung KW - Wasserdruck KW - Vorverformungen KW - Structural analysis of pipelines KW - rehabilitation KW - liner KW - snap-through loads KW - temperature impact KW - water pressure KW - initial deformations Y1 - 1991 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:836-opus-296 VL - 1991 IS - 1/2 SP - 50 EP - 55 PB - Oldenbourg Industrieverlag ER - TY - JOUR A1 - Falter, Bernhard A1 - Hain, Hans T1 - Stabilität von biegesteifen oder durch Momentengelenke geschwächten und auf der Außenseite elastisch gebetteten Kreisringen unter konstantem Außendruck T1 - Stability of elastically bedded circular rings - rigid or weakened by hinges - under constant outer pressure JF - Straße Brücke Tunnel N2 - Es werden die Verzweigungslasten von Kreisringen, die auf der Außenseite elastisch gebettet sind, nach der klassischen Stabilitätstheorie ermittelt und das Verhalten im überkritischen Bereich untersucht. Im Hinblick auf praktische Anwendungen werden sowohl Kreisringe mit Momentengelenken bzw. Momentenfedergelenken als auch biegesteife Ringe betrachtet. Als Ergebnisse werden die kritischen Lasten mitgeteilt und Hinweise für ihre Anwendung bei der Berechnung von Tunnelauskleidungen und unterirdischen Behältern gegeben. N2 - Bifurcation loads of circular rings, bedded at the outside, are treated by the classical approach. The behaviour in the post buckling region is investigated. For practical use circular rings without and with moment hinges and hinges with springs are examined. As a result the critical loads are given and hints for the design of tunnel linings und sub-ground tanks. KW - Kreisring KW - klassische Beullast KW - elastische Bettung KW - Wasserdruck KW - Momentengelenke KW - Circular ring KW - classical buckling load KW - elastical bedding KW - water pressure KW - moment hinges Y1 - 1975 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:836-opus-287 VL - 1975 SP - 98 EP - 105 PB - Ernst CY - Berlin ER - TY - JOUR A1 - Wittrock, Ulrich A1 - Vorholt, Christian T1 - Spatial hole burning in Yb:YAG thin-disk lasers JF - Appl. Phys. B N2 - The spatially varying intensity in a standing wave resonator leads to spatial hole burning in the gain medium of a laser. The spatial hole burning changes the gain of different longitudinal modes and can thus determine the optical spectrum of the laser. We simulate this longitudinal mode competition in standing wave resonators of thin-disk lasers. The resulting optical spectra of the laser are compared to measured optical spectra. We examine two types of resonators: I-resonators and V-resonators with different angles of incidence. In V-resonators, the non-normal incidence of the laser beam on the disk lifts the degeneracy of the polarization. Experiments show that the slight gain advantage for the p-polarization does not lead to polarized emission. For both types of resonators, the measured spectra are in good agreement with the simulated ones. The simulations allow to study the influence of spectral intra-cavity losses on the optical spectrum of a thin-disk laser. Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:836-opus-8234 VL - 120 SP - 711 EP - 721 ER - TY - JOUR A1 - Vorholt, Christian A1 - Wittrock, Ulrich T1 - Single-frequency oscillation of thin-disk lasers due to phase-matched pumping JF - Opt. Expr. N2 - We present a novel pump concept that should lead to single-frequency operation of thin-disk lasers without the need for etalons or other spectral filters. The single-frequency operation is due to matching the standing wave pattern of partially coherent pump light to the standing wave pattern of the laser light inside the disk. The output power and the optical efficiency of our novel pump concept are compared with conventional pumping. The feasibility of our pump concept was shown in previous experiments. KW - diode-pumped laser KW - solid-state laser KW - ytterbium laser Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:836-opus-10258 VL - 25 SP - 21388 EP - 21399 ER -